Industrial

Moisture Proof Strip Heater


Trivolt industries moisture proof STRIP heater is designed to resist to intermintent splashes of water and or plastic spills on the heater.
All ends and edges are fully sealed with our rotary welder. All termination is sealed with a brass cap that is silver brazed all around. All MPB heaters are manufactured with 24 gauge
stainless steel 304 2b stainless. For severe condition of water or plastic exposure Trivolt Industries can offer the MPBI, the MPBI is the same has the MPB but we fully submerse the heater under water to make sure that all welds and seals are 100% sealed.

Trivolt Industries adopts a stringent internal quality control system (QMSM-2009). Every heater is tested for resistance and dielectric. All our heaters are CSA, UL and CE approved.

  • Applications
  • Specifications
  • Construction
  • Electrical Connections
  • Clamping Methods
  • Holes
  • Wet environment
  • Nozzle tips (ground wire
  • Outdoor application
  • 35 wpsi
  • 800 deg f sheath temp
  • 1 piece construction
  • 60 inches max length
  • 1.5 inch min width
  • 6 inch max width
  • Lead wire
  • Stainless steel braid
  • Armor cable
  • text to come
  • Full strap barrel nut
  • Mounting tab
  • 3/8″
  • 1/2″
  • 5/8″
  • 3/4″
  • 1″
MPSH-1
  • Brass cap silver brazed all around
  • Stainless steel over braid exit (grounded wire)
  • Lead wire straight out
  • Option to seal wire with rubber shrink tube of Teflon sleeve
  • 60 inches max length
  • 1.5 inch min width
  • 6 inch max width
MPSH-2
  • Right angle brass cap silver brazed all around
  • Cap can be rotated at 90 – 180 – 270 or 360 degrees
  • Stainless steel over braid exit (grounded wire)
  • Lead wire straight out
  • Option to seal wire with rubber shrink tube or Teflon sleeve
  • 60 inches max length
  • 1.5 inch min width
  • 6 inch max width
MPSH-3
  • Brass cap silver brazed all around
  • Stainless steel armor cable exit (grounded wire)
  • Lead wire straight out
  • Option to seal wire withTeflon sleeve
  • 60 inches max length
  • 1.5 inch min width
  • 6 inch max width
MPSH-4
  • Right brass cap silver brazed all around
  • Stainless steel armor cable exit (grounded wire)
  • Lead wire straight out
  • Option to seal wire withTeflon sleeve
  • 60 inches max length
  • 1.5 inch min width
  • 6 inch max width
MPSH-5
  • Brass cap silver brazed all around
  • Stainless steel over braid exit (grounded wire)
  • Lead wire straight out
  • Option to seal wire withTeflon sleeve
  • 60 inches max length
  • 1.5 inch min width
  • 6 inch max width
Moisture Proof Strip Heater

Approvals & Certifications

All our manufactured heater elements are presently CSA and/or NRTCUL approved and/or CE certified. Our products are manufactured and controlled by our internal Quality Management System. This program allows TriVolt to track the quality of every component that make up our products and monitors the workmanship of every electrical heater and sensor manufactured and assembled in our facility.

CSA Std.C22.2. no 72-M1984
UL Standard 1030 6th Edition
EN 60335-1:2004
Shock and Vibration: IEC 61373; Category 1; Class B
CAN/CSA-C22.2 No. 72-10 (2013)
UL 499 Thirteenth Editions; Class 2871-02 and 2871-82.

TriVolt Industries can also comply with any customer specifications such as “Buy America”. Our facility in Westfield, MA, USA lends itself to perform final assembly of heaters and systems to accommodate any Buy-America content requirement.

We can also generate special test conditions with specific set-ups, use computer models to design or isolate problem areas.

We are continuously improving our manufacture methods and products through testing, research and development. Our high standards extend beyond our product line.

Payment methods

Copyright © 2024 TriVolt Industries. All Rights Reserved.